Gratuit

CN 7219

Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced"

✓ Couvert par le MACF Iron and steel

Aperçu du coût CBAM

Prix ETS actuel : 83.4 €/t CO₂. Exemple : 1 tonne de NC 7219 aux facteurs par défaut coûte ~17.97 € en certificats CBAM aujourd'hui.

Émissions directes
1.88 t CO₂/t
Émissions indirectes
0.275 t CO₂/t
CBAM cost (1000 t shipment)
€17,973
Comment est-ce calculé ?

Coût certificat CBAM = émissions intégrées × prix ETS × (1 − facteur de quotas gratuits) × majoration de phase.

Phase-in 2026: 10% of full certificate cost. Free allocation assumed 0% in this preview.

Calculer mon coût CBAM →

Principaux exportateurs vers l'UE

Eurostat Comext, dernière année disponible. Les volumes affichés sont les importations extra-UE (tonnes).

OrigineTonnes / anPart
China290,00034%
Taiwan220,00026%
South Korea180,00021%
India160,00019%

Source: Eurostat Comext annual extra-EU trade.

Comment se conformer pour ce code

Revu par l'équipe AutoCBAM — mis à jour 2026-04-28.

Methodology guide -- CN 7219 (stainless steel flat-rolled, ≥600mm wide)

Stainless flat is a high-value CBAM steel category dominated by China, Taiwan, South Korea and India. Per-tonne CBAM cost is higher than carbon steel due to the alloy content's embedded emissions.

Step 1 -- understand the production route. Stainless is EAF-dominated globally -- but the EAF here is a stainless-specific furnace fed with carbon steel + ferrochrome + ferronickel. Total direct emissions are 1.5-2.5 t CO2/t, slightly above the EU iron-steel default.

Step 2 -- watch for upstream alloy emissions. The chromium and nickel inputs carry embedded emissions of their own (ferrochrome ~3-4 t CO2/t Cr; ferronickel ~10-15 t CO2/t Ni). These are not separately declared under CBAM but are reflected in the supplier's scope 1 + 2 numbers when alloy production is on-site.

Step 3 -- request verified data; defaults under-state. The EU 1.88 t/t default is calibrated to carbon steel and is too low for stainless. Verified supplier data is more accurate -- and the verifier report should disclose the alloy mix and the upstream alloy emissions separately.

Step 4 -- handle Taiwan and South Korea favourably. Taiwanese stainless mills (Yieh United Steel, Walsin Lihwa) are EAF route; emissions sit at 1.5-1.8 t/t direct. Korean POSCO stainless is similar. Both jurisdictions have or are developing carbon pricing, opening Article 9 deductions over time.

Questions fréquentes

How is stainless steel emissions intensity different from carbon steel?
Higher per tonne but with different production routes. Stainless is dominated by EAF (with chromium, nickel additions) -- typical direct emissions are 1.5-2.5 t CO2/t. The chromium / nickel inputs themselves carry significant embedded emissions.
Are nickel and chromium inputs in CBAM scope?
No. The CBAM Annex I covers iron / steel products including stainless. Upstream nickel and chromium production is not in scope. The emissions factor for stainless is published in the EU defaults.
Does the AISI grade matter for CBAM?
Marginally. Higher-alloy stainless (e.g. 316 vs. 304) has slightly higher embedded emissions due to higher nickel content -- but the EU default is grade-agnostic.
Who are the largest exporters of CN 7219?
China (~290kt/yr), Taiwan, South Korea and India. China's share has grown as Russian / Belarusian flows are zeroed.

Recevoir un rapport coût-émissions

PDF gratuit avec les valeurs par défaut, les 3 principaux pays d'origine et une prévision de coût liée à l'ETS pour NC 7219.

Codes liés

Position parente: 7219

  • CN 72191100 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721912 — Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than h
  • CN 721913 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721914 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721921 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721922 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72192300 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72192400 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72193100 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721932 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than

Tous les codes du secteur Iron and steel →

Vérifier n'importe quel code NC →

Données de référence uniquement — la portée CBAM dépend de la déclaration TARIC et des dernières modifications de l'Annexe I.