Kostenlos

CN 7219

Flat-rolled products of stainless steel, of a width of >= 600 mm, hot-rolled or cold-rolled "cold-reduced"

✓ Vom CBAM erfasst Iron and steel

CBAM-Kostenvorschau

Aktueller ETS-Preis: €83.4/t CO₂. Beispiel: 1 Tonne KN 7219 kostet bei Standardfaktoren heute ~€17.97 an CBAM-Zertifikaten.

Direkte Emissionen
1.88 t CO₂/t
Indirekte Emissionen
0.275 t CO₂/t
CBAM cost (1000 t shipment)
€17,973
Wie wird das berechnet?

CBAM-Zertifikatskosten = eingebettete Emissionen × ETS-Preis × (1 − Freizuteilungsfaktor) × Einführungs-Markup.

Phase-in 2026: 10% of full certificate cost. Free allocation assumed 0% in this preview.

CBAM-Kosten berechnen →

Wichtigste Exporteure in die EU

Eurostat Comext, letztes verfügbares Jahr. Angegeben sind die Extra-EU-Importmengen (Tonnen).

HerkunftTonnen / JahrAnteil
China290,00034%
Taiwan220,00026%
South Korea180,00021%
India160,00019%

Source: Eurostat Comext annual extra-EU trade.

So setzen Sie diesen Code konform um

Vom AutoCBAM-Team geprüft — zuletzt aktualisiert 2026-04-28.

Methodology guide -- CN 7219 (stainless steel flat-rolled, ≥600mm wide)

Stainless flat is a high-value CBAM steel category dominated by China, Taiwan, South Korea and India. Per-tonne CBAM cost is higher than carbon steel due to the alloy content's embedded emissions.

Step 1 -- understand the production route. Stainless is EAF-dominated globally -- but the EAF here is a stainless-specific furnace fed with carbon steel + ferrochrome + ferronickel. Total direct emissions are 1.5-2.5 t CO2/t, slightly above the EU iron-steel default.

Step 2 -- watch for upstream alloy emissions. The chromium and nickel inputs carry embedded emissions of their own (ferrochrome ~3-4 t CO2/t Cr; ferronickel ~10-15 t CO2/t Ni). These are not separately declared under CBAM but are reflected in the supplier's scope 1 + 2 numbers when alloy production is on-site.

Step 3 -- request verified data; defaults under-state. The EU 1.88 t/t default is calibrated to carbon steel and is too low for stainless. Verified supplier data is more accurate -- and the verifier report should disclose the alloy mix and the upstream alloy emissions separately.

Step 4 -- handle Taiwan and South Korea favourably. Taiwanese stainless mills (Yieh United Steel, Walsin Lihwa) are EAF route; emissions sit at 1.5-1.8 t/t direct. Korean POSCO stainless is similar. Both jurisdictions have or are developing carbon pricing, opening Article 9 deductions over time.

Häufige Fragen

How is stainless steel emissions intensity different from carbon steel?
Higher per tonne but with different production routes. Stainless is dominated by EAF (with chromium, nickel additions) -- typical direct emissions are 1.5-2.5 t CO2/t. The chromium / nickel inputs themselves carry significant embedded emissions.
Are nickel and chromium inputs in CBAM scope?
No. The CBAM Annex I covers iron / steel products including stainless. Upstream nickel and chromium production is not in scope. The emissions factor for stainless is published in the EU defaults.
Does the AISI grade matter for CBAM?
Marginally. Higher-alloy stainless (e.g. 316 vs. 304) has slightly higher embedded emissions due to higher nickel content -- but the EU default is grade-agnostic.
Who are the largest exporters of CN 7219?
China (~290kt/yr), Taiwan, South Korea and India. China's share has grown as Russian / Belarusian flows are zeroed.

Emissions- und Kostenbericht erhalten

Kostenloses PDF mit Sektorstandardwerten, Top-3 Herkunftsländern und ETS-gekoppelter Kostenprognose für KN 7219.

Verwandte Codes

Übergeordnete Position: 7219

  • CN 72191100 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721912 — Flat-rolled products of stainless steel, of a width of>= 600 mm, not further worked than h
  • CN 721913 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721914 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721921 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721922 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72192300 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72192400 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 72193100 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than
  • CN 721932 — Flat-rolled products of stainless steel, of a width of >= 600 mm, not further worked than

Alle Codes im Sektor Iron and steel →

Beliebigen KN-Code prüfen →

Nur Referenzdaten — der endgültige CBAM-Anwendungsbereich richtet sich nach der TARIC-Anmeldung und der aktuellen Fassung von CBAM Anhang I.